加拿大Solinst不锈钢气囊泵407型

产品名称：不锈钢气囊泵
品牌：Solinst
产地：加拿大
型号：407


407型不锈钢气囊泵可在所有应用中提供一致、准确、可靠的地下水样品。确保在操作过程中不接触空气/水，泵是 VOC 采样的理想选择。
气囊确保驱动空气或气体不接触样品，从而避免样品脱气或污染。Solinst 膀胱泵坚固耐用。PTFE 气囊非常适合奉献，而更便宜的聚乙烯气囊可供那些喜欢在每次使用后更换气囊的人使用。只需几分钟即可在现场轻松更换膀胱和进气过滤器。无需特殊工具。
不锈钢泵非常适合常规流量或低流量采样，可以从地面以下 150 m (500 ft) 的深度提升。

 

低流量吹扫和取样：

低流量采样通过减少湍流提供优质样品。它还减少了吹扫量，从而减少了采样时间和处理成本。使用Solinst 464 型电子泵控制单元时，可以调整Solinst 膀胱泵以提供 100 毫升/分钟的连续输出。或更少。
在低流量采样期间使用流通池系统，可以在清洗水流动时在线连续分析它，以便在读数稳定后立即开始采样。
封隔器也可用于进一步减少吹扫量并加快采样时间。

 

407型不锈钢气囊泵的特征：

不锈钢： 1.66" Ø (42 mm) 和 1" Ø (25 mm)，316 不锈钢主体。
非垂直应用：泵几乎可以在任何角度有效运行，可以放置在垃圾填埋场、尾矿、储罐或污染物羽流下。
渗滤液/产品泵送：气动驱动泵非常适合泵送污染液体。可以轻松经济地泵送强溶剂和腐蚀性化学品。
经受住干抽、脏空气和沙子： Solinst 气囊不会因在含有沉积物的水中或干抽条件下运行而损坏。
防冻套件：可选配件可用于防止样品管线中的冻结。

 

407型不锈钢气囊泵的好处：

高质量样品：始终如一的准确样品，具有出色的 VOC 样品完整性。
简单：控制器、空气压缩机和流通池可以由一个人轻松运输到任何地点。通过压缩配件连接到泵。
节省成本：减少重复抽样的需要，缩短每轮抽样所需的时间。低吹扫体积确保快速取样。
气囊：耐用的不含 PFAS 的 PTFE 气囊非常适合奉献。也可以使用廉价的聚乙烯。


407型不锈钢气囊泵由 316 不锈钢制成，并配有 PTFE 止回球。**常用的气囊是 PTFE，但也可以使用聚乙烯气囊。这是大多数类型的市政、工业和一般环境应用的理想采样泵，尤其是在样品的 VOC 分析很重要的情况下。

标准 Solinst 气囊泵的泵体是方便的 1.66" 直径（42 毫米），长度为 2 英尺和 4 英尺（0.6 m 和 1.2 m）。1" 直径。(25 mm) 气囊泵也可用于较窄的应用和滑铁卢多级系统。


Solinst 气囊泵有 1" 和 1.66"（25 毫米和 42 毫米）不锈钢材质可供选择。



中文内容来自机器翻译，内容仅供参考，实际内容可参考原厂介绍或以合同为准。
英文原文：

Bladder Pump：
The Solinst Bladder Pump allows consistent, high quality samples in all types of applications. It offers excellent performance and reliability. With Solinst Bladder Pumps there is the assurance that there is no air/water contact during sampling. It meets the most rigorous US EPA standards for VOC groundwater monitoring.

The bladder ensures that drive air or gas does not contact the sample, thus avoiding degassing or contamination of the sample. Solinst Bladder Pumps are rugged and long lasting. PTFE bladders are ideal for dedication, while less expensive polyethylene bladders are available for those that prefer to change bladders after each use. Bladders and intake filters are easily replaced in the field in just a few minutes. No special tools required.

Excellent for either regular flow or low flow sampling, the stainless steel pumps can lift from depths up to 150 m (500 ft) below grade.

 

Low Flow Purge and Sampling：
Low flow sampling offers excellent quality samples by reducing turbulence. It also reduces purge volumes, and thus sampling time and disposal costs. When using a Solinst Model 464 Electronic Pump Control Unit, the Solinst Bladder Pump can be adjusted to provide continuous output of 100 ml/min. or less.

Use of a Flow-Through Cell System during low flow sampling, allows the continuous analysis of purge water, in-line, as it flows, so that sampling can begin as soon as the readings stabilize.

Packers are also available to further reduce purge volumes and to speed sampling times.

 

Features：
Stainless Steel: 1.66" Ø (42 mm) and 1" Ø (25 mm) with 316 stainless steel body.
Non-Vertical Applications: Pumps operate effectively at almost any angle and can be placed under landfills, tailings, storage tanks or contaminant plumes.
Leachate/Product Pumping: Pneumatic drive pumps are well suited for pumping contaminant liquids. Strong solvents and corrosive chemicals can be easily and economically pumped.
Survives Dry Pumping, Dirty Air and Sand: Solinst bladders are not damaged by operation in sediment laden water, or in dry pumping conditions.
Freeze Protection Kit: Optional accessory available to prevent freezing in the sample line.

 

Benefits：
High Quality Samples: Consistently accurate samples with excellent VOC sample integrity.
Simplicity: The controller, air compressor and flow-through cell can be easily transported by one person to any site. Hookup to the pump is by compression fittings.
Cost Savings: Reduced need for repeat sampling and shorter time required for each sampling round. Low purge volumes ensure rapid sampling.
Bladders: Durable PFAS-free PTFE bladders are ideal for dedication. Inexpensive polyethylene is also available.


The Solinst Bladder Pump：
Solinst Bladder Pumps are manufactured from 316 stainless steel and have PTFE check balls. The bladder most frequently used is PTFE, however polyethylene bladders are also available. This is the ideal sampling pump for most types of municipal, industrial and general environmental applications, especially where VOC analysis of the sample is important.

The pump body of the standard Solinst Bladder Pump is a convenient 1.66" dia. (42 mm) and comes in lengths of 2 ft and 4 ft (0.6 m and 1.2 m). 1" dia. (25 mm) bladder pumps are also available for narrower applications and for use in the Waterloo Multilevel System.

---

提示：“加拿大Solinst品牌407产品”内容及图片来自厂商官网、翻译或互联网引用等，内容仅供参考，以最终签订合同为准，如有差错或异议可联系我们更改。