加拿大Solinst液体测量探头式水位计（101 P7）

产品名称：液体测量探头式水位计
品牌：Solinst
产地：加拿大
型号：101 P7


101 P7液体测量设备水位计带有P7 探头的Solinst 101水位计采用极其耐用的激光标记 PVDF 扁平胶带，具有更厚的增强狗骨设计，减少了对井套管侧面的粘附。
 
潜水探头测量水位和总井深
使用位于探头尖端的传感器进行更一致的测量
Solinst PVDF 扁平胶带提高了抗拉强度和电效率


101 型水位计是便携式手动仪表的行业标准，用于测量井、钻孔、立管和水箱中的水深。它们坚固、易于使用，读数精确到 1/100 英尺或每毫米。

101 P7 型水位计具有额定为 500 psi的耐压探头和激光标记的 PVDF 扁平胶带。




准确的：
每 1/100 英尺或毫米的标记
可溯源至国家标准
灵敏度可调到电导率
探头可避免级联水中的错误读数
 
可靠的：
永久性激光打标
带不锈钢导体的非拉伸 PVDF 扁平胶带

长寿：
坚固、防腐蚀的组件
坚固、灵活的胶带
易于拼接和维修

灵活的：
PVDF 替换胶带可与其他仪表互换

增强的激光标记胶带功能：
耐用的 PVDF 非拉伸胶带
改进的电气性能
较厚的狗骨设计可防止粘在井边
每 1/100 英尺或每毫米永久激光打标

PVDF 扁平胶带每 1/100 英尺或每毫米激光打标一次；长度可达 5000 英尺 (1500 m)。新的扁平胶带通过在每个导体中使用 6 股镀铜不锈钢和 13 股不锈钢提高了抗拉强度和电气效率。P7 水位计探头经过精心设计，可浸入 1000 英尺（300 m）。探头尖端的传感器在井、钻孔和级联水中提供始终如一的准确测量，位移几乎为零。

PVDF 激光打标水位带：
101 P7 型水位计使用极其耐用的PVDF 扁平胶带，可追溯至 NIST 和欧盟测量标准。每根带状导体包含13股不锈钢和6股镀铜钢，使胶带不拉伸，抗拉强度和电效率高。胶带采用厚狗骨设计，可防止粘附在潮湿的表面上，并使其在应用中笔直悬挂。胶带也很容易拼接。

3/8" (10 mm) 胶带每 1/100 英尺或每毫米带有永久性激光标记，长度可达 5000 英尺 (1500 m)。

LM2：英尺和十分之一：每 1/100 英尺标记一次。
LM3：米和厘米：每毫米标记一次




Solinst 101 型 P7 和 P2 水位计可提供如下所示的卷轴，标准长度如下：


小卷轴    * 100 英尺。    30米
              * 200 英尺。    60米
              * 300 英尺。    100米
中卷轴    * 500 英尺。    150米
              * 750 英尺 。    250米
              * 1000 英尺。   300米
大卷轴    1250 英尺        400米
              1650 英尺        500米
              2000 英尺        600米

*聚乙烯胶带仅提供这些长度



P7水位计探头：
P7 探头可潜入水下 1000 英尺 (300 m)，因此，您可以在理想条件下测量总井深。探头尖端的传感器提供一致的测量，几乎为零位移。如果需要，胶带密封塞设计允许快速轻松地更换探头。
尺寸：直径 5/8 英寸，长 5.38 英寸（16 毫米 x 137 毫米）
重量： ~4.5 盎司（128 克）



中文内容来自机器翻译，内容仅供参考，实际内容可参考原厂介绍或以合同为准。
英文原文：

101 P7 Submersible Probe measures water levels and total well depth
More consistent measurements with sensor located at the tip of probe
Solinst PVDF flat tape has increased tensile strength and electrical efficiency

The Solinst 101 Water Level Meter with P7 Probe features an extremely durable, laser marked PVDF flat tape, with an enhanced dog bone design that is thicker, reducing adherence to the side of well casing.

Enhanced Laser Marked Tape Features：

Durable PVDF non-stretch tape
Improved electrical properties
Thicker dog bone design prevents clinging to sides of the well
Permanently laser marked every 1/100 ft or each mm

The PVDF flat tape is laser marked every 1/100 ft or each mm; lengths up to 5000 ft (1500 m). New flat tape has increased tensile strength and electrical efficiency by using 6 strands of copper coated stainless steel and 13 strands of stainless steel in each conductor. The P7 Water Level Meter Probe is engineered to allow submersion to 1000 ft. (300 m). Sensor at the tip of the probe provides consistently accurate measurements in wells, boreholes, and cascading water, with almost zero displacement.

With a stand-alone design, convenient carrying handle, and sturdy probe holder, the standard reels are ergonomically designed for ease of use. They are robust and smooth running. The battery is housed in a convenient drawer in the front of the reel, allowing quick replacement. The reels are equipped with an on/off sensitivity switch, light, buzzer, battery test button, brake and a tape guide stored on the frame.

Length Options：

Solinst Model 101 P7 and P2 Water Level Meters are available on reels as shown below, in the following standard lengths:

Small Reel        * 100 ft.    30 m
                         * 200 ft.    60 m
                         * 300 ft.    100 m
Medium Reel    * 500 ft.    150 m
                         * 750 ft.    250 m
                         * 1000 ft.    300 m
Large Reel           1250 ft.    400 m
                            1650 ft.    500 m
                            2000 ft.    600 m
* Polyethylene tapes are only available in these lengths

Water Level Meters    Model 101
solinst  water level meters  measure depth of water in wells  water wells  boreholes  depth of water  depth of water in wells  depth of water in boreholes  depth of water in standpipes  water level indicators  water level indicator for piezometer image

For measuring the depth to water in wells, boreholes, standpipes, and tanks, Model 101 Water Level Meters are the industry standard for portable hand operated meters. They are sturdy, easy to use and read accurately to 1/100 ft. or each millimeter.

There are two versions to choose from. The Model 101 P7 Water Level Meter features a pressure-proof probe rated to 500 psi and laser marked PVDF flat tape.

The Model 101 P2 Water Level Meter features an easy-to-repair probe and heat embossed polyethylene flat tape.

Also available, are the less expensive Model 102 and 102M Coaxial Cable Water Level Meters for use in small diameter tubes, and the basic Model 101B Water Level Meter (see Model 102 and 101B Data Sheets).

Features

Accurate:

Markings each 1/100 ft. or millimeter
Traceable to national standards
Sensitivity adjustable to conductivity
Probes avoid false readings in cascading water

Reliable:

Permanent laser markings
Non-stretch PVDF flat tape with stainless steel conductors

Long Life:

Rugged, corrosion proof components
Strong, flexible tapes
Easy to splice and repair
 
Flexible:

PVDF replacement tapes are interchangeable with other meters

Laser Marked Flat Tape：

Durable, non-stretch PVDF flat tape
Accurately marked each mm or every 1/100 ft
Tape splice option maintained
Certified Traceable to National Standards
 
PVDF Laser Marked Water Level Tape：

The Model 101 P7 Water Level Meter uses extremely durable, PVDF flat tape, traceable to NIST and EU measurement standards. Each tape conductor contains 13 strands of stainless steel, and 6 strands of copper-coated steel, making the tape non-stretch and high in tensile strength and electrical efficiency. The tape has a thick dog bone design that prevents adherence to wet surfaces, and allows it to hang straight in application. The tape is also easy to splice.

The 3/8" (10 mm) tapes come with permanent laser markings every 1/100 ft. or each millimeter, in lengths up to 5000 ft. (1500 m).

LM2: Feet and tenths: with markings every 1/100 ft.
LM3: Meters and centimeters: with markings every mm

Operating Principles：
Model 101 Water Level Meters use corrosion proof stainless steel probes attached to permanently marked flat tape, fitted on a well-balanced reel. They are powered by a standard 9 volt battery.

The probes incorporate an insulating gap between electrodes. When contact is made with water, the circuit is completed, activating a loud buzzer and a light. The water level is then determined by taking a reading directly from the tape at the top of the well casing or borehole.

A sensitivity control allows the buzzer to be turned off while in cascading water, and ensures a clear signal in both high and low conductivity conditions.

 

Polyethylene Tape：
The Model 101 P2 Water Level Meter uses high quality polyethylene tape that reels smoothly, remains flexible and hangs straight in the well. Heat embossed marking each millimeter or 1/100 ft. allow accurate readings. The 3/8" (10 mm) wide tapes come in lengths up to 1000 ft. (300 m).

Seven stranded stainless steel conductors resist corrosion, provide strength and are non-stretch. They make the tape very easy to repair and splice. The dog-bone design reduces adherence to wet surfaces.

M2 Feet and tenths: with markings every 1/100 ft.
M3 Meters and centimeters: with markings every mm

---

提示：“加拿大Solinst品牌101 P7产品”内容及图片来自厂商官网、翻译或互联网引用等，内容仅供参考，以最终签订合同为准，如有差错或异议可联系我们更改。